Informuojame, kad šioje svetainėje naudojami slapukai (angl. cookies). Sutikdami, paspauskite mygtuką „Sutinku“ arba naršykite toliau. Savo duotą sutikimą bet kada galėsite atšaukti pakeisdami savo interneto naršyklės nustatymus ir ištrindami įrašytus slapukus.
Kategorijos

Airsoft (šratasvydžio) ginklas GFG42 (ASCU Gen.4 version)

Laikinai nėra

Turite klausimų apie šią prekę?

KLAUSKITE

Gamintojas:GFC Guns
Prekės kodas:GFP-GFG-01-010594
Prieinamumas:Laikinai nėra
Kaina: 202.00€
Kiekis:Į krepšelį

Airsoft (šratasvydžio) ginklas GFG42 (ASCU Gen.4 version)



Dalį produktų aprašymų pateikiame anglų kalba. Jei turite klausimų  dėl produktų techninių specifikacijų, savybių, panaudojimo ar saugaus elgesio taisyklių kreipkitės telefonu +370 67954145 arba elektroninio pašto adresu info@amunicija.lt. Ačiū, kad pas lankotės ir perkate. Didelis Airsoft/šratasvydžio -  ginklų pasirinkimas garantuotas.

Ginklo aprašymas ir specifikacijos anglų kalba:

 

GFG42 carbine replica (ASCU2 Gen.4+ version)

GFG42 is made from metal and durable polymer. The stock pipe, outer barrel, RIS rails, iron sights and all sorts of small elements such as trigger, magazine release button or fire mode selector are made from metal. The body, stock and profiled pistol grip as well as RIS rails linings are made from polymer.

The replica features a top, 22mm RIS rail and a set of front RIS rails as well as a collapsible stock. Due to collapsible stock with a pad with anti-slip texture it is possible to adjust the length of the stock to the body type and user’s preference. The replica has a 14mm, left-hand thread.

The battery included in the set is stored in the stock. The replica has a mini connector and MOSFET module. Reinforced TORQUE-UP gears, metal spring slide, reinforced gearbox skeleton and reinforced piston with metal teeth increase the longevity of the replica. The motor with increased torque together with low resistance wires provide increased efficiency.

This replica has been outfitted with the most up-to-date gen.4+ ASCU2 module, installed in our service department.

In the latest ASCU gen.4+ module we receive an updated software that will protect it against damages caused by a low quality Li-Po battery.

The ASCU is a two-part electronic module ( the control module and the sensor module ) which, upon being installed in the Airsoft replicas, significantly improve their operation. The traditional joint module was replaced with a sensor module which monitors the actual position of the piston thread-wheel, the firing mode selector lever and the trigger. The gathered information is sent to the control module – in which the software located in the processor analyzes it and controls the replica’s motor with the use of the MOSFET active break.

ASCU Gen. 4 includes the following upgrades: 

1. New MosFet transistors with 16 times less resistance, resulting in to faster cycle, better active brake, more shots per battery charge and less heat.
2. New very strong trigger switch.
3. New reinforced design with full polymer encasing.
4. Better short-circuit protection.
5. Easier installation.
6. Updated software with easier programing (accidental hop-up program activation is impossible).
7. Improved cut-off lever.
8. Improved selector plate.
9. Fits all standard and reinforced version 2 gearboxes.
10. 3 year world wide warranty.

The ASCU improves the operation of a V.3 gearbox and makes that the replica equals the more expensive replicas and the more sophisticated PTW class replicas. The ASCU system monitors the operation of the replica no matter the speed of squeezing the trigger and is responsible for the full cycle of the piston’s operation, both in the semi-automatic and full automatic firing modes. The piston stops in the starting position after each shot.

The ASCU is equipped with the Low Drain Protection system which is specially designed to secure the lithium-polymer (LiPo) batteries from being damaged.

In case of any emergency, the ASCU stops the firing mode in the replica and, therefore, secures the inner elements from further damage.

The ASCU is easy to install in the replica which is equipped in the V.2 gearbox. Most of the models does not require the modification of the airsoft rifle’s original parts. Yet, in some cases, some minor changes may have to be introduced – thanks to this the installation process will be completed without any problems.

NOTE:
11,1V or 12V Battery is recommended!
7,4V to 8,4V Battery to be used only with M90 up to M100 springs.
The use of high quality motor with  ASCU2 gen.4+ is highly recommended.
The use of high quality battery with  ASCU2 gen.4+ is highly recommended.

The set includes:

- replica
- magazine
- RIS covers
- battery
- battery charger

 

Prieš įsigydami Airsoft/šratasvydžio-  ginklą pasiteiraukite pas mus ir tikimės, kad galėsime Jums pateikti patrauklesnį pasiūlymą nei mūsų konkurentai Lietuvoje ar kitose Europos šalyse.


Atsiųsk nuorodą su kitur išsirinktu Airsoft/šratasvydžio  - ginklu ar aksesuaru elektroninio pašto adresu info@amunicija.lt ir gauk mūsų pasiūlymą pasirinktam modeliui.

Šiuo metu, kartu su partneriais, savo pirkėjams siūlome, bene plačiausią Airsoft/šratasvydžio-  ginklų ir aksesuarų pasirinkimą.


Ne visi, mūsų siūlomi, ginklai ir aksesuarai yra pateikiami elektroninėje parduotuvėje www.amunicija.lt , todėl teiraukitės papildomai ir tikimės, kad nenusivilsite.


Atsiliepimų apie šia prekę nėra.

Parašyti įvertinimą

Jūsų vardas:


Jūsų apžvalga:Pastaba: HTML nėra išverstas!

Įvertinimas:Blogas           Geras

Įveskite kodą apačioje: